| 2018 |
|
P7-2018-72 (400.796)
Tsyganov Yu. S. et al.
Low Background Techniques for Heavy Nuclei α-Decay Registration
Methods of rare event α-decay registration applied in the last years
at the Flerov Laboratory of Nuclear Reactions are under consideration. Special
attention is paid to the consideration of development and application of
method of active correlations and different algorithms for real-time
applications of correlated sequences and beam association background
suppression.
|
P7-2018-71 (524.333)
Tsyganov Yu. S.
REDSTORM2 — Ñ++ Program Package for New Gas-Filled Recoil Separator of FLNR (JINR)
C++ program package for new FLNR (JINR) Gas-Filled Recoil Separator is presented.
This version of the software is in fact a deep upgrade of former REDSTORM program. It will be applied together
with DSSSD focal plane detector and time-of-flight gaseous detector of the separator in the experiments aimed at the search of rare α-decays of superheavy nuclei.
Program for storage of spectrometry data operates with applying of active correlation technique.
Programs modeling the experiments to search for correlation chains in a real-time mode as well as simple tests
of electronics apparatuses are under consideration too. For those purposes a specific pulse generator and external α-decays sources are used.
|
E13-2018-70 (249.352)
Volkov A. D., Kravchenko M. D., Pavlov A. V.
The Test Bench for Studying the Characteristics of Straw Tubes
The design and technical parameters of the stand developed for studying the characteristics of thin-walled tubes (straw)
are given. The method of measuring straw characteristics with a diameter of 9.8 mm and a wall thickness of 20 μm
is described, and the results are presented. The area of elastic deformation, which extends to a tension of
(1.85 ± 0.02) kgf, was determined. A tension more than this value leads to elastoplastic deformation at which the
tension relaxation and creep rate of the straw material increase. The elastic modulus of the tube material which is equal
to (4.44 ± 0.05) · 109 N/m2 was measured. The results of the elasticity modulus' temperature dependence
studies allow selecting the optimal operating temperature for straw detector. Poisson's ratio of the tube material,
which is required to estimate the change in its tension in vacuum, was determined. Its value was 0.338 ± 0.004.
For a relaxation process, the presence of a semi-permanent residual tension on the time scale of a typical tracker
lifetime, which depends on the choice of the initial straw tension, was considered for the first time. The presented results show high accuracy of the measurements.
|
E13-2018-69 (235.049)
Plis Yu. A. et al.
Research and Development of the Polarized Deuteron Source for the Van de Graaff Accelerator
An attempt is made to develop a polarized deuteron source suited for the Van de Graaff accelerator of the Czech Technical University
in Prague. We relied on
Kaminsky's experiment on channeling deuterons through a Ni single crystal. The setup is described which contains permanent
magnets with a transverse magnetic field to increase the deuteron polarization using the Sona method (zero transition).
The measurements of tensor polarization were carried out with TiT target. The result is
Pzz = – 0.12±0.04 for a weak field at the target without channeling.
The ultimate aim is to produce 14-MeV polarized neutrons which will be used
jointly with the frozen-spin polarized deuteron target for measurement of ΔσT and ΔσL asymmetries in the nd-transmission experiment.
|
P2-2018-68 (484.545)
Dedovich T. G., Tokarev M. V.
Reconstruction of Dimension of Complete and Incomplete Fractals
The SePaC and BC methods are used for fractal analysis of mixed events containing incomplete fractals.
Reconstruction of the distribution of events by dimension DF is studied. The procedures for analyzing incomplete
fractals and correcting the determination of DF of combined fractals by the SePaC method are proposed.
We find that the SePaC method fully reconstructs incomplete fractals and suppresses background, separation
of incomplete fractals and background by the BC method depends on the basis of the formation of the fractal.
The distribution of events by value of DF is more accurately reconstructed by the SePaC method in comparison with the BC method.
|
P5-2018-65 (189.317)
Yamaleev R. M.
Representation of Solutions of the System of Riccati Equations via Operators of Divided Differences
Results of the action of divided difference operators on power and exponential functions are given by triangle matrices
with elements depending on coefficients of the characteristic polynomial. It is shown, if distances between nodes are tending to zero,
then the triangle matrices transform into the Pascal matrix. Invariant functions with respect to the operators of degenerated divided
differences are constructed. The generalized system of Riccati equations corresponding to high-order ordinary differential equations
and their solutions are presented via the divided difference operators.
|
E6-2018-64 (301.261)
Izosimov I. N.
Structure of β-Decay Strength Function Sβ (E) in Halo Nuclei, Spin–Isospin SU (4) Symmetry, and SU (4) Region
In heavy and middle nuclei, the energy EGTR of Gamow–Teller (GT)
resonance (GTR) is larger than the energy EIAR of isobar-analogue resonance (IAR), EGTR > EIAR.
In 6Li and 11Be nuclei for low-energy super-GT phonons (or GTR), we have EGTR < EIAR.
One of the consequences of Wigner's spin–isospin SU(4) symmetry is EGTR = EIAR.
Using these data we estimated that the value Z/N = 0.5–0.6 corresponds to the SU(4) region, where EGTR ≈ EIAR.
|
P10-2018-63 (1.035.595)
Morkovnikov I. A., Kirilov A. S.
System of Measurements Registration «Journal»
on the Spectrometers of the IBR-2 Pulsed Reactor
The work is devoted to the Journal system intended for automation of
registration process of measurements performed on the IBR-2 instruments. The
system concept, requirements to a data model and service are considered. The
offered concept was originally conceived as unified for the simplifying
adaptation to instrument specifics. Now the system is implemented on
spectrometers of YuMO, HRFD and GRAINS. The version for NERA instrument is
prepared for testing. In the near future the Journal system will
be supplemented with the ability to work with data in the
central repository of FLNP measurement results.
|
P4-2018-61 (123.018)
Pupyshev V. V.
Bohr—Zommerfeld Quatization Rule in the Case of Decreasing Power Potential
We study the finite three-dimensional movement of a quantum particle in the field of the potential
V(r) = –V0r–α with
the parameters V0 > 0 and α ∈ (0,2). We analyse the asymptotic equation which is equivalent to the Bohr–Zommerfeld
quantization rule. As a result, we derive a simple and explicit approximation for the energies of weakly bound states of this
particle.
|
P4-2018-59 (330.839)
Pupyshev V. V.
Two-Dimensional Movement of a Slow Quantum Particle in the Field of a Central Long-Range Potential
We study the two-dimensional movement of a slow quantum
particle in the field of a central long-range potential decreasing
in the limit of large distances r as a power function r–β
with the exponent β ∈ (1,2). For this particle, we found the
low-energy asymptotics of the phase-shifts and differential
cross-section, as well as a simple approximation for the energies
of weakly bound states.
|
E18-2018-58(515.244)
Pahomi A. et al.
Small-Angle X-Ray Scattering of Alginate Membranes Doped with CoFe2O4 Nanoparticles. Preliminary Results
Today, alginate is one of the most employed biopolymers in agricultural,
food and life science related industry, mostly due to its high-performance gelling and viscosity properties.
The initial industrial uses of alginates were as adhesive binders, however more recently they are extensively
applied as thickeners, emulsifiers, film and gel making substances. The complementary use of alginate and magnetic
nanoparticles can lead to new biomedical and biotechnological applications, including targeted drug delivery,
magnetic cell separation, enzyme immobilization, magnetic resonance imaging (MRI), and hyperthermia treatments.
|
P13-2018-57 (184.450)
Turek M. et al.
Simulation of Ionization in the Ion Source with a Hot Cone-Shaped Hollow
A numerical model of ionization in the hot blunted cone-shaped hollow is presented. The influence of the hollow geometry,
namely, the height and upper base radius, on the ionization efficiency was investigated. It is found that for the ionization
of stable isotopes the elongated hollow is more appropriate, while for the ionization of short-lived isotopes it is
preferable to use the shortened hollow. The dependence of the ionization efficiency on the extraction opening radius
and wall thickness was determined. The current–voltage curves for different ion source configurations are discussed.
|
E13-2018-55 (553.481)
Dunin N. et al.
Fire Extinguishing System Development for the Slow Control System of the
TOF-MPD
Human safety is considered a priority in modern society. No matter where
people are, at home or at work, they must feel confident and secure. To
ensure that, a fire protection system that would immediately send
information to safety equipment is required. Therefore, one of the main
functionalities is a design that would operate with alarm, fire
extinguishing devices and data acquisition software. Modern fire alarm and
fire fighting systems have been considered during the process.
|
P9-2018-52 (298.319)
Melnikov S. A., Meshkov I. N.
Investigation of Stability of Motion of Charged Particles in the LEPTA Storage Ring
Analytically calculated matrices of the optical conversion of the elements of the focusing system of the Low Energy Particle
Toroidal Accumulator (LEPTA) and the longitudinal magnetic field perturbations appearing in the technical connections
of the ring elements are presented. On the basis of the data of the matrices, a program was written that makes it possible
to model the multi-rotation dynamics of particles in a ring and thereby investigate the stability of their motion.
|
P19-2018-48 (253.638)
Krasavin E. A. et al.
The Influence of DNA Synthesis Inhibitors on the Biological Efficiency
of the Modified Bragg Peak Proton Beam
The effect of inhibitors of DNA synthesis of 1-β-D-arabinofuranosylcytosine (AraC) and hydroxyurea (HU),
the medicaments used in an oncological clinic, on the formation of double-strand breaks (DSB) of DNA in human cells
when irradiated with protons in the Bragg peak was studied. It is shown that in the presence of AraC and HU,
the biological efficiency of proton irradiation, estimated by the kinetics of γH2AX/53BP1 foci formation,
increases sharply in the post-radiation period. This is due to the formation of enzymatic DSB from long-time unrepairable
single-strand DNA breaks. Application of the proposed method, leading to an increase in the biological efficiency of proton beams,
significantly brings together the areas of use of proton and carbon accelerators for therapeutic purposes.
|
P13-2018-47 (1.744.253)
Azaryan N. et al.
The Minimization of the Long Term Noises of the 24-Bit ADC for the
Precision Laser Inclinometer
The daylong noises of the 24-bit ADC DT9824 and DT9828 in the laboratory
room conditions and in the thermo-stabilized and radio isolated laboratory
and the noises dependence on the single measurement duration have been
researched.
The ADC resolution in the temperature
stabilized and radio isolated conditions was improved significantly,
by a factor of 240. The ADC's relative
resolutions have been measured for a daylong period: 3 · 10–7
for DT9824 with 0.79 s for one measurement and 2 · 10–7
for DT9828 with one measurement duration of 0.10 s.
The innovative methods for accounting of the ADC noise temperature
variations were proposed and developed based on subtracting of one ADC
channel data from remaining ones. This method application resulted in the
improvement of the RMS values of an ADC relative resolution: by a factor
of 13 for DT9824 and by a factor of 6 for DT9828.
|
|
E11-2018-43 (178.602)
Török Cs.
Speedup of Interpolating Spline Construction
The article introduces an efficient sequential algorithm
for computing spline coefficients.
The aim is to decrease the computational time.
A reduced-size tridiagonal system of linear equations is constructed
based on a recently derived relation for the unknown coefficients
of uniform cubic splines of class C2 at the odd grid points.
The even coefficients are computed from an explicit formula.
Thanks to the half-size system and use of a simple formula,
the suggested new sequential algorithm needs less
division than the traditional one
and it results in a non-negligible computational speedup.
Finally, a general approach to dyadic reduction of the dimensionality
of tridiagonal linear systems is proposed in consequence of which the size
of the systems gradually shrinks to half, quarter, etc.
|
P9-2018-42 (355.502)
Golubkov E. A. et al.
A Triode Electron Gun of Linear Accelerator LUE-200, IREN Facility
The electron injector (electron gun) is a triode system (cathode-control
grid-anode with a second grid «wall») with a grounded anode and an isolated
filament shielded cathode, which is supplied with high-voltage (up to
-200 kV) pulse from the thyratron modulator through a pulse transformer.
A triode gun is an electron injector with the heated oxide-barium cathode
and a controlled startup on the grid cathode-grid node from the microwave
lamp GS-34.
Starting the
grid with adjustable delay to adjust the pulse duration from 40 to 400 ns
injected from the cathode beam is made from the starting pulse of the
cathode node from the first channel of the synchronizer. From the second
channel, the thyratron modulator is launched. As a result of adjustment,
a beam with a current pulse of 5 A at a focusing current of focusing
solenoid ML1 3.1 A at a voltage of 200-220 kV with a diameter of a beam
5 mm at a frequency of 25 Hz was obtained.
|
P13-2018-40 (1.502.736)
Vinogradov A. V. et al.
High-Flux Pulsed Neutron Source Driven by a Proton Accelerator for Beam Research
Parameters of the most optimal variant of a high-flux pulsed neutron source
(fourth-generation neutron source in Dubna), which is foreseen to replace the linebreak IBR-2M
reactor in the future, are considered. The source is based on a booster with a plutonium dioxide core
(multiplication factor of no more than 0.98) and a tungsten target. The source is driven by a proton accelerator with an energy of 1.2
GeV and beam power of 0.1 MW. The power of the source is 8 MW, pulse repetition rate is 30 s–1.
The possibility of obtaining the average thermal neutron flux density on the surface of a flat water moderator up to 2 · 1014 ñì–2 · ñ–1 is demonstrated.
|
E13-2018-39 (403.224)
Bielewicz M. et al.
Mobile and Multipoint Temperature Measurement Systems Based
on Pt100 Sensors for Future Study of Energy Emitted from the Uranium Experimental Assembly
The goal of our project was to construct simple and cheap devices which can simultaneously measure
temperature in many points. The system will be able to work on uranium experimental assembly in
high radiation environment like Quinta assembly of Energy + Transmutation RAW collaboration.
The Quinta assembly simulates Accelerator Driven Systems (ADS).
Knowledge about energy production inside installation like this is very important for the
future project of the IV-generation nuclear reactors. Designed Temperature Measurement System (TMS) gives possibility to obtain this
energy by using temperature changing measurement. The system was built by ready-to-use components. We focused on communicating
these devices with LabView self-prepared control program and developing a reliable calibration system. This paper presents construction way,
calibration procedure, and the first result of measuring.
|
E16-2018-38 (339.570)
Chlopik A. et al.
The Prototype Dosimetry System to Protect NICA Slow Control Electronic Equipment
During the work the Multi-Purpose Detector (MPD), which is a part of the Nuclotron-based
Ion Collider fAcility (NICA) located in Dubna, can burst in an accidental irradiation caused by NICA's
failure or its abnormal functioning. It can result in the presence of the radiation exposure in the room where
the Slow Control electronic equipment will be installed. Thus, there is a risk of destroying the electronics,
and as a consequence the emergency switch off of the NICA apparatus might become impossible.
The article describes the method of prevention of such a situation by the continuous dosimetry
monitoring in the Slow Control chamber and alarming when the radiation threshold is overrun.
|
E13-2018-37 (434.371)
Bielewicz M. et al.
MCORD — MPD Cosmic Ray Detector for NICA
The Multi-Purpose Detector (MPD) is a part of the Nuclotron-based Ion Collider
fAcility (NICA) located in Dubna, Russia. For full functionality, the MPD
needs an additional trigger system for off-beam calibration of MPD
subdetectors and for rejection of cosmic ray particles (mainly muons). The
system could also be useful for astrophysics observations of cosmic showers
initiated by high energy primary particles. The consortium NICA-PL composed
of several Polish scientific institutions has been formed to define goals
and basic assumptions for MPD Cosmic Ray Detector (MCORD). This article
describes the early stage design of the MCORD detector based on plastic
scintillators with silicon photomultiplier photodetectors for scintillation
readout and of the electronic system based on MicroTCA crate. Plans for simulations
of MCORD detector performance are also presented.
|
P16-2018-36 (569.506)
Mokrov Yu. V. et al.
The Correction of Albedo Dosimeter DVGN-01 Readings in Medical Beam Cabin by Various Methods
The paper presents the results of correction of albedo dosimeters DVGN-01 readings in the
medical beam cabin at the LNP phasotron by various methods. A beam of 170 MeV protons was stopped
in a tissue-equivalent phantom placed in the patient's chair. Using a multisphere spectrometer,
the neutron spectrum was measured near the chair, and measurements were made with the spherical
albedo system at the place of the neutron spectrum measurement and near the cabin wall.
Based on the neutron spectrum and the spherical albedo system readings, correction coefficients
were calculated for DVGN-01 in two geometries — isotropic and antero-posterior for the individual
dose equivalent and effective dose of neutrons. Recommended values of correction coefficients for use in individual
dosimetric control of persons accompanying patients in the cabin of a medical beam are presented.
|
E13-2018-30 (259.663)
Chirikov-Zorin I. et al.
Performance of Shashlyk Calorimeter Read Out by SiPMs with High Pixel Density
The matrix of 3 × 3 modules of the EM calorimeter ECAL0 (COMPASS II) read out
by MPPC S12572-010P SiPM with the pixel density of 104 mm-2 and an
area of 3 × 3 mm is studied in the range of electron energies 1–30 GeV. It is
observed that MPPC has additional response nonlinearity and a
significantly smaller dynamic range of output signals than expected. The
mechanism of the effect based on the influence of parasitic capacitance
between pixels on the pixel gain is proposed. The energy resolution of the
calorimeter is measured to be (σE/E) = (7,1%/√E)(1+0,06/E)⊕1,4%E0,25
|
P18-2018-29 (3.800.785)
Komarov V. I.
The start of the creation of the medico-biological complex at the proton beam of the JINR synchrocyclotron
The first step in the creation of the medico-biological complex at the proton beam of the JINR Laboratory of Nuclear Problems cyclotron is considered.
|
P13-2018-28 (1.160.652)
Pepelyshev Yu. N., Rogov A. D., Sidorkin S. F.
Optimization Study of the Accelerator-Driven Multiplying Pulsed Neutron Sources
The neutron source operating at the Frank Laboratory of Neutron Physics
of the Joint Institute for Nuclear Research (Dubna) on the base of the IBR-2M pulsed
reactor with the flux density of thermal neutrons ∼ 1013cm-2 · s-1 will
exhaust its resource and be shut down by 2034. It is proposed to consider the proton-driven
subcritical pulsed neutron source instead of the IBR-2M. At present, the world mostly uses the
nonmultiplying neutron sources based on the high-current proton accelerators, for example, SNS or ESS with a
beam power of 3 and 5 MW, respectively. We present the computational comparison of the various categories of the
high-current proton accelerator-driven pulsed neutron sources in order to select the most optimal solutions.
The one-zone booster with a tungsten target and the core with plutonium dioxide which can be a promising option is shown.
For such a source, it is possible to obtain an average thermal neutron flux density of more than 5.0 · 1014 cm-2 · s-1 at a
proton beam power of 0.1–0.2 MW.
|
P10-2018-23 (549.125)
Kirilov A. S., Morkovnikov I. A.
About the Concept of the File Repositary for Istruments at the IBR-2 Pulsed Reactor
The work is devoted to the concept of a central repository of measurement data from the IBR-2
instruments at the FLNP, JINR. The concept takes into account the variety of structures and data file formats
on specific instruments, the users' wishes, and estimated amount of disk space required. The questions of the
service organization for the work with the data into the storage were considered, taking into account the existing
system of automatic measurements registration Journal.
|
E13-2018-22 (622.408)
Korepanova N. V. et al.
Neutron Noise Analysis Using the Basic Element Method
The full range of noise energy pulses reaches ±22% under normal
conditions of operation of the IBR-2M reactor (JINR, Dubna). Therefore, slow changes in average power, caused,
for example, by the movement of regulatory bodies, “drown” in the noises. But in a number of cases,
it is these slow components of the pulse energy variation, the so-called basic signals (baseline),
that are of fundamental importance for justifying the conditions for safe operation of the reactor.
To determine the baseline in the noises of the IBR-2M the sixth order mean-square piecewise polynomial approximation (MSPPA-6)
was used for the detection of the baseline in the noises of IBR-2M. The algorithm MSPPA-6 depends on control
parameters α, β, M and K, the optimal values of which depend on the initial noise parameters.
The algorithm was applied to both the static and the dynamic state of the reactor in the range of an average power
of 30 kW – 2 MW. The average processing time of one point on a PC x86_64 Processor Intel Core i5-4570 Sandy Bridge machine,
3.20 GHz, was 0.05 ms, which allows using the MSPPA-6 algorithm in real time.
|
P3-2018-20 (552.724)
Zakharov M. A. et al.
Numerical Simulation of the Experiment on Observing Non-Stationary Diffraction of UCNs on a Moving Lattice
A set of programs has been created for modeling the experiment to study UCN diffraction on a moving grating.
The problem of diffraction of neutrons on a lattice with parameters corresponding to the actual experiment was solved
numerically on the basis of the equations of the dynamic theory of diffraction. The process of measuring the diffraction
spectrum by a time-of-flight Fourier diffractometer was simulated by the Monte Carlo method. Systematic errors in the reconstruction
of the neutron energy spectrum by the inverse Fourier spectrometry method are investigated. The results of numerical calculations are
compared with experimental data.
|
E1-2018-18 (763.504)
Suchopár M. et al. (on behalf of the Collaboration
“Energy and Transmutation of Radioactive Waste”)
Activation Measurement of Neutron Production and Transport in a Thick Lead
Target and a Uranium Blanket during 4 GeV Deuteron Irradiation
Several simple accelerator-driven system (ADS) setups were irradiated with
relativistic proton and deuteron beams in the last years at the Nuclotron
synchrotron site of the Joint Institute for Nuclear Research (JINR) in
Dubna, Russia. This paper is dedicated to a 4 GeV deuteron irradiation of a
setup called Energy plus Transmutation (E + T), consisting of a lead target,
natural uranium blanket, and polyethylene shielding. This paper represents
the finalization of data analysis and concludes systematics of the proton
and deuteron experiments carried out with the E + T setup. Activation
detectors served for monitoring of proton and deuteron beams and for
measurements of neutron field distribution in model ADS studies. Products of
reactions with thresholds up to 106 MeV as well as non-threshold reactions
were observed in the samples. The yields of the produced isotopes were
determined using the gamma-ray spectrometry and compared with Monte Carlo
simulations performed with the MCNPX transport code.
|
P11-2018-17 (311.312)
Ayryan E. A., Malykh M. D., Sevastianov L. A.
Finite Differences Method and Integration of the Differential Equations in Finite Terms
We show that standard approaches to integration of the differential
equations in finite terms contain the reference to numerical methods of the last centuries.
Further we describe the class of the differential equations of the first order allowing
good differential schemes. This means that the calculation by such scheme can be continued after mobile singularities.
After necessary introduction we describe such one-to-one scheme for the Riccati equation and prove its property mentioned above.
In conclusion we present n-to-n schemes for 1st order differential equations as their natural generalization.
Here we prove that one-to-one schemes exist only for the Raccati equation and investigate conditions of existence of 2-to-2 schemes.
|
E1-2018-11 (1.393.237)
Tokarev M. (on behalf of the STAR Collaboration)
Recent STAR Spin Results and Spin Measurements at RHIC
The STAR experiment provides measurements of single- and double-spin
asymmetries in longitudinally and transversely polarized p+p collisions at √ s = 200 and 510 GeV
to deepen our understanding of the proton spin structure and dynamics of parton interactions over a wide range of collision energy,
momentum and rapidity of the various produced probes. Polarized processes with W± production allow us to study the spin-flavor
structure of the proton. Recent results obtained by STAR on the double longitudinal asymmetry, ALL, of pion and
jet production at √ s = 200 and 510 GeV, the single longitudinal, AL, and transverse,
AN, asymmetry of W± production at √ s =510 GeV are overviewed.
STAR results on azimuthal single transverse asymmetry of pion in p↑ + (p, Au)- and jet + π± â p↑ + p collisions are discussed.
The proposed Forward Calorimeter System (FCS) and Forward Tracking System (FTS) upgrades at STAR would significantly
improve the capabilities of existing detectors for measurements of observables such as asymmetries of pion, jet, Drel–Yan pairs produced at forward rapidities.
|
E3-2018-7 (250.576)
Granja C. et al.
Two Methods of Determination
of Parities of Low-Lying States
in 159Gd from Analysis of
γ-Ray Intensities from
158Gd(nres,γ)159Gd Reaction
Energy levels and transitions in 159Gd were studied
by means of radiative capture of resonance
neutrons in 12 isolated resonances of 158Gd.
The time-of-flight technique was used on an enriched
target at the IBR-30 reactor at JINR, Dubna.
A total of 80 primary gamma transitions were recorded,
and their absolute intensities were determined resulting
in the observation of 1/2± and 3/2± levels up to
2.4 MeV.
Parities of the found levels were recalculated using two methods:
the first method consists in analyzing of intensities averaging
in 12 resonances, and in the second method individual intensities
are analyzed. The second method is described for the first time.
|
P11-2018-6 (746.926)
Akishin P. G., Sapozhnikov A. A.
The Integral Formulation of the Magnetostatic Problem for Magnetic System Modelling
We consider the application of the volume integral method to the magnetic system
calculations. The major stages of modelling process are discussed:
the discretization of initial equations, the description of the algorithm
for dividing the area into elements, the calculation of matrix elements for
discretization problem and the solution for the obtained system of non-linear
equations. The results of modelling of magnetic systems using the discussed method are presented and compared with calculations performed by other programs.
|
P2-2018-4 (837.094)
Sinegovsky S. I., Sorokovikov M. N.
Prompt Atmospheric Neutrinos in the Quark-Gluon String Model
We calculate the prompt atmospheric neutrino flux in the energy
range 1–105 TeV arising from decays of the charmed particles. Cross sections
of the D-mesons and Λc-baryons production in pA- and πA-collisions
are calculated in the framework of the phenomenological quark-gluon string model,
free parameters of which were improved using measurement data of the LHC experiments.
Predicted prompt neutrino flux is compatible with the constraint obtained in IceCube experiment.
Also we compare our calculation with other predictions obtained for different charm production models.
|
P15-2018-3 (4.377.077)
Didyk A. Yu. et al.
Synthesis of Solid-State Structures and Chemical Elements under Irradiation by Bremsstrahlung γ Rays with a Maximum Energy of 10 MeV in Condensed Deuterium at a Pressure of 2.2 kbar
A high-pressure chamber filled with deuterium (DHPC) under initial pressure 2.2
kbar was irradiated during 49 h by bremsstrahlung γ rays with a maximum energy of 10 MeV.
After irradiation, several particles with dimensions up to 1 mm fell out of the DHPC.
On the inner surfaces of the DHPC, newly formed solid micro-objects
were found in the form of crystalline and amorphous microparticles, filaments,
nodules and inclusions. Investigations of the elemental composition of the revealed structures,
carried out with the help of X-ray microprobe analysis, showed the presence of chemical
elements in them, which were absent in the reaction chamber prior to the onset of irradiation.
The following chemical elements were registered: 6C, 7N, 8O, 11Na, 12Mg,
13Al, 14Si, 15P, 16S, 17Cl, 19K, 20,
21Sc, 22Ti, 24Cr, 25Mn, 26Fe, 28Ni, 30Zn,
33As, à òàêæå îëîâî 50Sn è ñâèíåö 82Pb.
The experiment on the synthesis of chemical elements in deuterium confirms
the results of previous experiments performed with other gases: hydrogen, helium and xenon.
|
2018-1 (14.227.816)
Brief Review of Topmost Scientific Results Obtained in 2017 at the Joint Institute for Nuclear Research
|
